How To Install A Rear View Camera On A Roll Back Truck

Download Article

A rear-view camera, likewise known as a backup camera, lets you see what's behind your vehicle without having to look backwards. Though the device comes standard with many new car models, you lot can add a rear-view camera to your vehicle if it didn't come with one.

1
Buy a mountable backup camera for your specific vehicle. For safety, make sure you purchase a device specifically designed to exist a rear-view camera. Purchasing one fabricated for your specific vehicle will make it easier to install than a standard aftermarket camera. So you can install it easily, look for a photographic camera that mounts onto or directly behind your license plate.^[one]
- Await for backup cameras at consumer electronics stores.
2
Get an external monitor if you want to keep your existing rear-view mirror. An external backup monitor is a small video screen that mounts onto your windshield similarly to a GPS. Though they take up more space than internal monitors, external monitors are far easier to run into and tin can be easily replaced if necessary.
- If you'd similar, you tin can employ a standard video monitor instead. However, keep in mind that it may not have all the aforementioned features as devices designed for use with backup cameras.
Advertisement
3
Purchase an internal monitor for a less obtrusive device. An internal backup monitor is a fully functioning rear-view mirror that houses a small-scale screen within the drinking glass. Some internal monitors clip on pinnacle of your current rear-view mirror, merely others replace your original mirror entirely.^[two]
- Most internal monitors shut off and disappear when not in use, making them a perfect option if you want to preserve your automobile's looks.
4
Buy ability and video cords if your camera and monitor didn't include them. For most rear-view camera installations, you'll demand photographic camera and monitor splitter cords with connectors for video and power cables, 2 bare wire power cables, and an RCA video cable.^[3]
- Most installation kits include these cables, only some may crave you to buy them separately.
- Some camera models apply wireless transmitters instead of standard video cables.

1
Take off your rear license plate. Using a Phillips caput screwdriver, remove each of the screws holding your rear license plate in identify. Then, pull the plate off and set up it aside.^[four]
- Make sure yous identify the screws in a safe place so yous don't lose them.
2
Remove your trunk's interior panel. Pop open your trunk and look for a solid interior console covering the opposite side of your license plate mounting area. So, insert a trim removal tool or other sparse device behind the panel and pry it off.^[5]
- Removing this panel will betrayal the machine'southward rear wiring chambers.
3
Drill a pocket-size hole in the license plate mounting area. Make sure there are no obstructions between the license plate mount and the rear wiring chamber. And so, create a small hole in the car using a power drill equipped with a loftier-speed twist drill bit. Line up your hole so it is directly behind where your camera's power and video cablevision will become.^[6]
- To effigy out where to make the hole, agree your camera up to the area yous intend to mount it. And then, note the spot where its splitting string sits.
- Create a hole that'southward large enough to fit your camera's ability and video cablevision.
- If you come across any obstructions, try to remove them. If yous tin't, see if you can brand a hole nearby.
- For about jobs, you'll need a drill bit that has a diameter between ¹⁄₈ and ¹⁄_four in (0.32 and 0.64 cm).
4
Place a rubber grommet around your camera cable. Before running your camera cablevision into the car, slip a rubber grommet onto it near the non-splitting end. These pocket-sized rubber washers, bachelor at most abode improvement stores, will keep the wire in place and prevent leaks.^[vii]
- Choose a grommet that'south merely large enough to fit inside the drilled pigsty.
5
Run the photographic camera cable into your body. Pull the splitting cease of your camera'south video and ability cable through the drilled hole into the torso of your car. Make sure you lot pull it tight so the safe grommet lodges into the drilled hole.
- Your photographic camera cable should run from the exterior of the machine to the inside of the car.
half dozen
Locate your car's ii contrary low-cal wires. Reverse light wires are the cords that connect your car'southward tail lights to the dashboard. They claw directly into your vehicle'south tail lights and are usually located in the hatch or trunk of your car.
- These cords look different for every vehicle so, if y'all can't find them, consult your possessor's transmission for model specific data.
7
Strip and separate your car'south contrary light wires. Using a wire stripper or pliers, peel back the rubber covering the wires. Then, use a screwdriver or other thin tool to poke a hole through the middle of each exposed wire, separating the individual wire strands.^[viii]
- For prophylactic, make sure you lot do this while the car is turned off.
8
Fuse your camera wires with the opposite light wires. Attach i of your blank wire cables to the camera cord'southward ability connector. And so, poke your bare wires through the center of the exposed reverse light wires and twist them together. For safety, make sure you lot wrap the combined wires in electrical tape.^[nine]
- Brand certain you poke your positive (usually blood-red) bare wire through the positive reverse light wire and the negative (commonly black) bare wire through the negative contrary light wire.

1
Route your camera's video cable to the front of the auto. Connect your RCA cable to the photographic camera string'south video connector if necessary. Then, run it through your vehicle to the area past the fuse box. Depending on your vehicle model, you'll usually be able to do this by peeling back the auto'southward headliner or side panels and pulling your cable through the exposed bedroom.^[10]
- For certain trucks, you may demand to run the video cable through the vehicle's frame track.
- In most cars, you'll find the fuse box underneath the steering cycle.
two
Fix external monitors to the front windshield. If you're installing an external monitor, first adhere your device's included mount to the windshield by following the manufacturer's included instructions. So, hook your monitor onto the mount.
- Almost external monitors use a suction mountain, though others may come with a more complex mounting organization.
three
Attach internal monitors to the rear-view mirror or mirror mount. For sure internal monitors, you lot'll demand to clip the new device onto your current rear-view mirror. For others, you'll need to have off the mirror and slide your monitor into the pre-existing mirror mount.^[11]
- Some internal monitors may come with their own mounting system that you'll have to attach to the machine's front windshield.
4
Run the monitor'due south splitter cablevision to the fuse box. If necessary, hook your monitor'southward power and video cable into the device. Then, route the cable from the monitor to the area adjacent to the fuse box.^[12]
- If you'd like, use a trim removal tool to pop out the headlining console directly above your windshield. Then, run your cable through the exposed chamber.
5
Connect your monitor's camera cable to the RCA cable. After routing your monitor's splitter cable, connect the video stop of the cablevision to your camera'south RCA string. Then, wrap the continued cords with electrical record to hold them together.
- If your RCA and video cables accept the same ends, you may need to purchase an RCA male to female converter cord. You tin can notice these at most electronic stores.
6
Attach your monitor's power cable to a fuse tap. Connect your remaining bare wire cable to the fill-in monitor's power cord. Then, push the positive (normally crimson) end of the bare wire cable into the open finish of a fuse tap. Finally, crimp the 2 cables together with a pair of pliers.^[13]
- A fuse tap is a small cable that converts a bare wire into a fuse bespeak. You can find them at virtually auto part stores.
- If you'd prefer, you tin exit the bare wire cable off and connect your camera's power cable to a cigarette lighter adaptor. And so, plug this adaptor into your car'south cigarette lighter receptacle for power.
7
Plug the fuse tap into the fuse box. Locate your fuse box and open it up. Then, plug your fuse tap into an open up fuse prison cell. If necessary, check your fuse box's lid or your vehicle's instruction manual to see which slots are open.^[14]
- After attaching your fuse, consider taping all your wires together using electrical tape to get them out of the mode.

1
Connect your fill-in camera to its power and video cablevision. Return to the back of your car in one case you've installed the rear-view monitor and all the necessary camera cords. Close the trunk if necessary, then connect the fill-in camera to its power and video cable.
- Your camera'south power and video cablevision should be sticking out of the hole you drilled in the license plate mounting area.
ii
Mountain the camera to your license plate. If the camera attaches to the front of your license plate, fix it to the plate by following the manufacturer'south included instructions. If the camera attaches to the back of your license plate, line the device up with the plate's fastener holes and thread screws through them.^[xv]
- In most cases, you lot can adhere a rear-view camera to the back of your license plate using the screws you lot removed from the automobile earlier.
iii
Reattach your license plate and trim panels. Using a Phillips head screwdriver, put your rear license plate back on your vehicle. Once yous've reattached it, requite the license plate and fill-in camera firm tugs to brand sure they're secure.
- If you lot haven't already, reattach your car'south interior trunk console and other trim panels by pressing them back onto the vehicle.
4
Test the camera to make sure everything works. Before using your new camera on public roads, exam it in a condom area like your driveway. If it turns on, identify a large, durable object similar a trash can backside the camera to see how distorted the paradigm is. If it does not turn on, read your installation transmission for troubleshooting data.
- In many cases, rear-view photographic camera malfunctions are caused past loose or improperly connected wires.

Add together New Question

Question

I hooked the camera up and information technology only flickers. Any communication?

You may want to ensure all cables and connections are secured tightly. Double check that all connections are right. If this doesn't piece of work, check to see if the photographic camera called is in good shape and isn't physically damaged.
Question

Suzuki installed opposite parking camera in my Swift Dzire Zxi. But the photographic camera shows upper view and not the ground below. What tin I do ?

Brand certain that the camera is installed the right manner (not upside downwards), and check the position of the photographic camera mounted. Take it back to the dealer that installed information technology and ask them to check the alignment and fit.
Question

What is the best height for a reversing camera?

In that location is no optimal height for a back-up camera. The platonic height is based off the specific machine or vehicle that you have and your personal preferences, along with its intended awarding. Some back-up cameras are placed on large service trucks so that they tin can line up to trailer hitches easier, some are to foreclose a blindspot on the road. Depending on your application, information technology can be placed at any height. Most reversing cameras are a "wide view" style and the specific height location does not always touch the way it functions.
Question

Then if I hooked upwards all the wires correctly but nonetheless no power, is information technology a fuse tap that I need to splice into the wires for it to piece of work correctly?

Shannon Phillips

Community Answer

Check your globe or ground it may be bad. Utilize your multimeter to come across if the footing is okay.
Question

Is information technology still okay to connect the back-up camera to the reverse light with cars that accept machine lighting? Or, would I need to connect to the reverse wire on the gearbox?

Shannon Phillips

Community Answer

Yes, that volition exist fine, that how information technology is supposed to be washed. Look for an auto electrician if you need someone to call.

Enquire a Question

200 characters left

Include your email accost to get a message when this question is answered.

Submit

Though most auto dealers and mechanics will non install aftermarket fill-in photographic camera systems, many audio and electronic shops will.

Make certain you turn the car off before working with bare or stripped wires. If you need to touch exposed wires while the automobile is on, put on a pair of daze-resistant rubber gloves.

Advert

Things You'll Need

Rear-view camera
Rear-view monitor
Connector cables
Phillips head screwdriver
Trim removal tool
Ability drill with high-speed twist flake
Prophylactic grommet
Wire stripper or pliers
Electric tape
Fuse tap

Well-nigh This Article

Article Summary 10

To successfully install a rear-view camera, first remove your vehicle'south rear license plate and interior trunk panel. Using a power drill, punch a small-scale hole through the exposed license plate mounting area and run your photographic camera's ability and video cord through it. Attach a blank wire power cable to your photographic camera's power connector, so strip your auto's reverse low-cal wires and splice them with your bare wire power cable. To learn how to mountain the rear-view photographic camera and backup monitor, scroll down!

Did this summary help yous?

Thanks to all authors for creating a page that has been read 263,253 times.